遠立行工業股份有限公司

登入

加入會員

求助

遠立行工業股份有限公司

	Recommended Results

產品型錄

共10 筆產品

選取全部

全部取消

1. UCP 200 SERIES

This unit type is the most popular unit and is used in many kinds of the transmission devices. This type is fixed at the shaft in a simple and reliable manner by means of the set screws hexagonal holes prepared in the inner ring. UKP type is ...

2. FC housing type

The figure of housing is square with 4 bolts. The shaft diameter and dimensions are the same as 722500 series. GLH FC housings can exchange with SKF housings

3. SEAL

TACONITE SEAL, LABYRINTH SEAL, ZF SEAL, FELT SEAL, RUBBER SEAL, OIL SEAL AND ETCS...

4. PILLOW BLOCK

PILLOW BLOCK AS FOLLOWING SERIES

1:UCP (UKP) 200 & 300 series,
2:UCF (UKF) 200 & 300 series,
3:UCFL (UKFL) 200 & 300 series,
4:UCT (UKT) 200 & 300 series,
5:UCFC (UKFC) 200 & 300 series,

5. SPLIT PLUMMER BLOCK

SN SERIES IN SOLID BASE
SN & SSN SERIES, 200, 300, 500, 600, 3000 & 3100 series (Solid Base),
HOUSING RANGE 506-532, 607-632, 207-232, 307-332, 3024-3052, 3122-3132.
SHAFT DIA 25~140,40~140, 30~140, 35~160, 110~170, 100~140 mm
APPLICATION DESIGN TO VAIORUS SEALING, LIKE FELT SEAL, ZF SEAL, TAC, OR TS SEAL.
End cover EP, if bearing is mounted at the end of a shaft.
SOLID BASE SSN ARE APPLICABLE FOR HEAVY LOADING AND THERE'S OPTION OF MATERIAL RANGING FROM CAST IRON FC200, DUCTILE IRON FCD450, AND CAST STEEL SC460.

6. ADAPTER SLEEVE

ADAPTER(WITHDRAWAL) SLEEVE,NUT, & WASHER,

1.ADAPTER SLEEVES IN H30, H31, H2, H32, H3 SERIES

2.WITHDRAWAL SLEEVES IN H23, AH30, AH240, AH31, AH241, AH22, AH32, AH3, AH23 SERIES.

3.LOCKNUTS AND LOCKWASHERS IN EITHER INCH SIZE OR MATRIC SIZE.

7. SPLIT PLUMMER BLOCK

SD SERIES
SERIES SD3100 SD3000 SD500 SD600
HOUSING RANGE 3134 - 3180 3034 - 3076 534 - 564 634 - 656
SHAFT DIA 150 ~ 380 mm 150 ~ 360 mm 150 ~ 300 mm 150 ~260 mm
APPLICATION Design to handle higher load rating and moderate speed.
LUBRICATION Grease standard, circulating oil lubrication available.
SEAL SELECTIONS Labyrinth(TS)with rubber O cord, Taconite seal(TAC)
End cover(TSA) if bearing is mounted at the end of a shaft.
REMARK Four bolt mounting with eye bolts on the top for easy handling.

8. Plummer block

1.design to handle extreme heavy loads
2.L.E.R, Taconite seal (TAC) End cover(E.P.R) if bearing is mounted at
the end of a shaft.
3.SDAF series availabe for 4 bolt mounting.
*SDAF200 & SDAF300 are suitable for stepped cyclindrical shafts

9. Split Plummer block

SDAF SERIES
SERIES SDAF 500 SDAF 200
HOUSING RANGE 520 - 544 220 - 244
SHAFT DIA
(inch measurement) 3 7/16 ~ 7 15/16 4 1/2 ~ 9 9/16(d1)
3 3/16 ~ 8 5/16(d0)
APPLICATION design to handle extreme heavy loads.
LUBRICATION grease or ...

10. Split Plummer block