|
|
 |
Recommended Results |
| |
|
|
| 公司介紹 |
| |
CHILL ROLLS FOR ROLLING MILLS.
The rolls are double poured duplex rolls and are manufactured by the advance centrifugal process. Duplex rolls have the advantage of selecting the harder best performing material on the working surface, which is primarily a Cr-Ni-Mo alloyed chill cast iron & a relatively softer material inside. After casting the rolls are annealed to relieve the internal stresses thus improving the strength of the material. After heat treatment the rolls are proof machined & fitted with Steel shaft to close tolerance.
These rolls are manufactured for section mills producing rounds, squares, flats, Hexagon, Gate Channel as well as mills producing Tor steel and Tmt bars.
We also provide Single poured Chill Cast iron rolls for angle and Channels
CHILL ROLLS FOR NON METALLURGICAL PURPOSES
These rolls are manufactured for
· Roller Flour Mills
· Oil Mills
· Paper Calendaring Machines
· Solvent Extraction Plants
· Rubber Mixing Mills
· Crushing plants/ Sugar Plants
· Paint plants
· Cereal and Grain Processing
· Chocolate refiners and Food Processing
· Rice Flaking
· Oil Seed Crushing and Flaking
· Pellet Crumbling
· Coffee Grinding
· Biscuit and Confectionery Plants
The rolls are double poured duplex rolls and are manufactured by the advance centrifugal process. Duplex rolls have the advantage of selecting the harder best performing material on the working surface, which is primarily a clear carbon chilled cast iron or a Cr-Ni-Mo alloyed chill cast iron & a relatively softer material inside. After casting the rolls are annealed to relieve the internal stresses thus improving the strength of the material. After heat treatment the rolls are machined & fitted with spindles from both sides. Fluting is also done on the roll surface as per requirement of the customer.
FORGED ROLLS:
We manufacture forged rolls in the grades M.S., En8, En9, En19, En24, En31, En42, Etc as per customer’s requirement. Rolls are manufactured up to a diameter of 24” (Max) & maximum Weight of 3 Tonnes.
Most of the rolls being used as roughing rolls for rolling mills and for rolling heavy sections
ADAMITE ROLLS
These Rolls are special hyper-eutectoid steel rolls alloyed with Nickel, Chromium & Molybdenum. The extra Carbon and special alloys give extra wear resistance and strength.
These rolls are statically cast and undergo a special high temperature heat treatment process of double annealing followed by tempering cycles to give a micro structure consisting of fine pearlitic matrix with spherodised / broken carbide.
These Rolls are suitable for rolling medium and heavy sections where resistance is very important along with considerable amount of strength and toughness. These rolls are also used for roughing stands of strip mill
ROLLING MILL MACHINERY:
We provide complete rolling mill machinery as per customer’s requirement on turnkey basis.
With an experience of over 2 decades we have witnessed the infinite changes in the industry and can recommend and provide the best possible solution for any problem faced during the erection and the production process.
We also provide Spares for rolling mills including
· Fibre Bearing
· Gears
· Gearbox, Reduction gear box
· Gear Coupling
· Universal coupling
· Stands
· Bearing Chokes
· Shearing Machines
· CI Coupling, CI Rail, etc
GEAR COUPLING & GEARS
Gear Couplings are used to couple two shafts.
Advantage of gear coupling over rigid flange coupling being that
· A slight misalignment is permissible between the two shafts.
· Considerable reduction in the jerks as compared to those, which exists in flange coupling.
· Longer life
Gear for pinion gearbox and reduction gearbox
Gears are manufactured in grades En9, En19, En24 as per design requirement.
FIBRE BEARING
Fibre Bearings are moulded from Plastic Laminate of select Cotton fabric, bonded with phenol Formaldehyde Resin. It has wide Industrial Applications
SPECIAL CHARACTERISTICS
1. The very low coefficient of friction, when wet, it enables reduction in POWER consumption.
2. Being highly resistant to abrasion, it also considerably reduces roll journal wear
3. Its large loading capacity brings about higher efficiency of the machine.
4. Water, the cheapest lubricant, can be used on the Bearings thus dispensing with the costly use of lubricating oils and / or greases.
5. The specific gravity of Phenolic Plastic is 1.36, which is approximately 1/ 5th of any nonferrous metal.
6. Machines using Fibre Bearings have longer services, performance and high production efficiency.
CENTRIFUGAL CASTING:
We also undertake centrifugal casting like bushes, liners, etc as per the requirement of the customers
Company Profile :
Established in 1991, Jagdev Industries was started as a manufacturer of chilled rolls in Sinnar, Nasik (about 180 Kms from Mumbai – the commercial hub of India). Today we are the leading rolls manufacturers, serving a wide variety of customers.
With our endower to manufacture quality chill rolls at par to the satisfaction of our prestigious customers, we at Jagdev industries leave no stone unturned in impart quality to our products. It may be from selecting the best raw material of our products, to testing during each stage of the production process to the final testing, each of our product matches the requirement of the each industry in terms of quality, performance & service.
Establishment Year
Firm Type
Nature of Business
Level to Expand
: 1991
: Proprietorship
: Manufacturer
: International |
| 相關產品 |
| |
chill, chilled, roll, rolling, flour mill, paint mill, ink plant, rubber mixing rolls, paper calendering, solvent extraction, gear, gearbox, stand, fibre bearing |
| 公司基本資料 |
|
| 公司名稱: |
Jagdev Industries |
| 連絡: |
聯絡我們
|
| 網址: |
********
|
| 電話: |
91-253-2595536 |
| 傳真: |
91-253-2595536
|
| 國家: |
印度 |
| 住址: |
B-98,STICE,Sinnar |
|
| 產品櫥窗 |
|
|
|
|
|
